* We independently evaluate all recommended products and services. If you click on links we provide, we may receive compensation.
Is this the case that your Maytag centennial washer won’t start all of a sudden? Can’t understand whether it happened due to a stuck-on sensing, power surge, or an error code? If so, you will have no option but to reset the machine.
Disconnecting the power may be a way to force a washing machine to reset, but that depends on which model and type of Maytag washer you’re using. Given that you’re using a Maytag centennial washer, you’ll need better solutions to reset the machine.
Deciding which reset method will be the ideal fit for your washer will depend on whether your washer has a button control panel or a dial (mechanics), a top-loader or a front-loader, and its age.
To get the step-by-step reset guidance that is prepared explicitly for your Maytag washer model, you’ll most likely have to find the best Maytag centennial washer manual, also referred to as the repair or technical manual.
Nevertheless, this repair guide of ours will serve the purpose and provide you with all the information you need to reset your washer model seamlessly. So, let’s start.
When To Reset Your Maytag Centennial Washing Machine?
Knowing ‘how do I reset my Maytag Centennial HE washer’ will be beneficial when the following circ*mstances arise:
When You Have To Clear The Error Codes
Attempt to reset your washing machine if you lack sufficient knowledge on how to elucidate and clear a particular error code.
Although it should be your last option (which we will discuss here), a reset will help you clear the majority of the Maytag centennial error codes.
If an error code can’t be fixed, consider using the Maytag washer reset code.
When The Maytag Washing Machine Won’t Start
In the majority of situations, the Maytag washing machine may refuse to start due to a stuck button, water supply issue, locked controls, wrong setting, and power issues.
Still, even if you address these issues, you may find the machine not starting. In that case, it’s best to fix the machine by resetting it.
When The Machine Starts Making Weird Noises
Your Maytag machine may start making weird noises, from banging and grinding to squeaking and rattling noises. In such a situation, if you fail to understand the issue, choose to reset the washing machine.
Also, it’s crucial you check for possible foreign items, such as pins and coins, and get rid of them before you commence the resetting solution.
When The Machine Refuses To Move To The Subsequent Cycle
If your washing machine refuses to move to the next phase of the washing cycle and you fail to understand its reason, you can choose to reset it.
Before that, you must consider the likelihood of a defective filter, leakage, failing heater, or drainage problem. Preventing the machine from transitioning to the next cycle could be one of the reasons.
When The Washing Machine Refuses To or Don’t Spin
The Maytag washing machine may refuse to spin due to reasons like a component failure, wrong setting, unstable washer, overload, or uneven load. At times, you can resolve it by resetting it.
So, consider rebooting the Maytag washing machine if you plan to repair anything. That must happen after you do laundry rearranging and washer stabilization.
When The Machine Refuses To Agitate
If your Maytag washer doesn’t agitate, restart it. That’s the solution only when you can’t understand why the machine refuses to agitate. In the majority of cases, the reasons are quite the same as a washing machine that refuses to spin.
Thus, it’s best to consider problems like component failure, washer imbalance, wrong setting, overload, and load imbalance.
When The Machine Is Stuck-On Sensing
Although it’s important to evaluate the lid lock, water valve for faults, control board, shift actuator, timer, and lid lock when your washing machine is stuck on sensing, a reset may be the only viable option at times. Thus, start considering resetting the Maytag machine if it refuses to pass through the sensing cycle.
When There’s Replacement of a Critical Washing Machine Component
It’s recommended to recalibrate your washing machine after the replacement of a critical component. Explicitly, you must perform it after the replacement of the motor, main control board, or breaker.
You must bypass the errors that are likely to occur and reset the washing machine to make it ready for the wash.
When The Washing Machine Lid Starts Malfunctioning
At times, the washing machine lid won’t unlock or lock. That sometimes happens because either the lid lock or switch is malfunctioning.
You can use a multimeter to test the two. If they work just fine and you can’t comprehend what’s the issue, start resetting the machine and attempt to close the machine lid.
When There Is a Power Failure
Once there is a mid-cycle power failure, it’s best to reset the washer. In case of such a power failure, you’ll receive an error code, which can be cleared off via reset.
7 Effective Methods To Reset Your Maytag Centennial Washer
Here are the most effective ways by which you can reset your Maytag Centennial washer easily and conveniently:
1. Unplugging The Machine For 20-Seconds
This method calls for unplugging your Maytag Centennial washer for 20 seconds before plugging it back in, as even the name would imply. In the event that your initial effort is unsuccessful, try two or three times again.
Essentially, this reset technique can successfully reboot the circuit board and breaker while clearing the majority of error codes.
2. Unplugging The Machine For 10-Minutes
Try 10 minutes when the 20 seconds of disconnecting doesn’t help, specifically if you’ve tried it two or three times already.
Simply disconnect your washing machine, wait ten minutes, and then plug it back in. The error code shouldn’t be present once you restart the machine. If so, go for the recalibration method.
3. Recalibration Method
Not only for the Centennial but for any Maytag washing machine, this is perhaps the most successful approach. It is advised to follow the replacement of a motor, control board, or actuator, among other essential components.
The steps are as follows:
- Put your washer in standby mode by plugging it in but without turning it on.
- The cycle selector (key knob) should be turned anticlockwise until it reaches the 12 o’clock position.
- To activate the diagnostic mode, rotate the knob three times towards the right, then once each to the left, right, and back again.
- When the “rinse” LED turns on, rotate the key knob in a clockwise manner.
- To begin the recalibration, click start
4. Reset Via Power-Start Option
To use this method, you must:
- Press the power button and turn the washer off.
- Remove the washing machine’s power cord.
- Hit the start button for 5 to 10 seconds after starting a fresh cycle.
- Reconnect the machine to the power source and turn it on.
5. Power Cancel Reboot Method
For both the Centennial washer and other Maytag washers, the power cancel reboot is a successful reset method. A washing machine that won’t advance to the subsequent cycle can also be reset using this method. You should:
- On your Centennial washer, press the pause/cancel button.
- Select the appropriate wash cycle.
- To finish the reset, hit the start/pause button on the device.
6. The Lid Lift Method
The steps listed below are involved in the lid lift tactic:
- Remove the washing machine’s power supply.
- Reconnect it after a brief period.
- The washer’s lid should be swiftly raised and then lowered quickly (within 12 seconds, try getting six rounds)
- Normalize the washer’s start-up
7. 12 ‘Clock Dial
The Centennial versions that include a dial upon that control panel are compatible with this method. It enables you to run a checkup on your Centennial washing machine and recalibrate it.
So, if you were searching ‘how to reset my Maytag control panel,’ follow these steps and get your answer:
- The 12 o’clock position can be reached by turning the dial.
- It should be rotated anticlockwise to its starting position.
- Now, rotate it counterclockwise to the third position.
- When the control panel LED begins to flicker, rotate the main dial counterclockwise to the 3 o’clock position.
- When the rinse light turns on, flip it in the opposite direction.
- To begin the calibration, click start.
Maytag Centennial Washer Error Codes & Troubleshooting
The most common reason to reset a Maytag washer is because of washer error codes. These error codes indicate a particular issue with the machine.
The procedures listed below must be followed to obtain these error codes:
- The first step is to turn off the power to your washing machine.
- To complete a full rotation, turn the machine control dial a minimum of three times in a 360-degree motion to the right.
- Rotate the knob three clicks to the right, one click to the left, and one click to the right while your hands are on it.
Note: There should be a 0:05 to a 1-second interval between each click.
The error codes might not be accessible when you turn the knob for more than a second between clicks.
- The washer’s lights will flash once you’re successful. “Manual diagnostics,” “Automatic Diagnostics,” and “View Stored Error Codes” are the three choices you’ll see.
- Turning the knob to the right can access “View Stored Error Codes.” Wait until the “Done” light is on before stopping.
- Click “Start.”
- You can now see the error messages that are presented on the washer.
- Even when there are more Centennial washer problems, the machine will only display the most recent four.
The Maytag Centennial Washer contains a number of trouble codes. Some of them consist of the following:
- Sud or Sd: This indicates that the washing machine has too many suds.
- F8 E1 or LO FL: The machine has detected a low water flow.
- F5 E2: Poorly locked door.
- F7 E1: Denotes a problem with the motor speed sensor.
Ending Note
So, if your Maytag Centennial washer develops issues, follow these steps to reset it. If none of the aforementioned techniques successfully reset your Maytag machine, the control board may malfunction. It is better to leave the diagnosis and repair of a control board problem to a qualified professional.
FAQs
1. What is the Maytag Centennial washer model?
The Whirlpool Corporation released the belt-driven Maytag Centennial washer in late 2010. The washer machine was introduced as an energy-saving, low-cost washing machine. The majority of the latest Maytag Centennial washing machines come with model numbers starting with MVW.
2. What is the easiest way to reset my Maytag Centennial washer?
The simplest way to reset the Maytag centennial washing machine is unplugging it two to three times with a time interval of 20 seconds. If it doesn’t work, try unplugging it for about ten minutes.
3. Is reprogramming my Maytag Centennial washer possible?
The best way to reprogram your Maytag centennial washer is by turning off the washing machine, unplugging it from the power source, beginning the latest cycle, and hitting the start or reset button. This way, you can recalibrate the machine and eliminate the error codes.
4. Does the Maytag washing machine consist of any reset button?
The Maytag washing machine comes with several factory settings and functions, but the reset button option isn’t one of them.
5. How do I find the reset button on my Maytag washing machine?
To find out the reset button on your Maytag washing machine, adhere to these steps:
- Press the ‘Spin’ and ‘Soil’ buttons for ten seconds simultaneously.
- The console will display a countdown.
- After the countdown has finished the unit, the machine will get reset successfully.
6. How can I reset my Maytag washing machine after a power outage?
If you’ve encountered a power surge and intend on resetting the Maytag washing machine, here’s what you must do:
- Initially, start checking the electric circuit box.
- Then, start pushing off and turn 360 degrees and pull it back.
